Monday, January 21, 2008

Chapter 6 - Fuselage exterior - Part 3

It's been quite cold lately. A little too cold to be working in the garage. Today it was a little warmer and comfortable enough to do some sanding and mix up some micro to fill in the some little gouges in the foam exterior.

I think that I am ready to glass the exterior and move onto the next chapter, however I would prefer that temperatures are quite a bit warmer than they have been lately. Perhaps I will wait a month to do that.

In the meantime I have ordered the main gear strut from Featherlite. It should be shipping next week. I will post some photos when it arrives.





Pictured here is a view of one of the fuel site gauges. I really do not think that this will be an effective fuel gauge due to the amber tint of the glass. I will likely order a pair of Vance gauges.
In addition I would like to install a pair of electronic gauges as well.



Thursday, January 17, 2008

Chapter 6 - Fuselage exterior - Part 2

I am still not quite finished contouring the bottom, but I got bored and decided to flip the fuselage over and do some work on the top. Again this was kind of time consuming, but fun.






























Also, just for fun I printed some scale images of some instruments I am considering. It is way early to be thinking about these things in my opinion, but its fun, and that the whole reason I am building this to begin with.

Monday, January 14, 2008

Chapter 6 - Fuselage exterior - Part 1



I have started contouring the fuselage exterior. The plans say this step should take only 3 hours. I think that is quite a strech, but perhaps I am just being timid in removing the foam. Still this has been pretty fun. It's nice to see the box shape transformed to an aircraft exterior.

Chapter 6 - Fuselage bottom - Part 4

I have finally finished chapter 6!

There are a couple of things that did not quite go as planned though.With the cold weather I anticipated the epoxy would cure a little slower than expected. the plans call for a 2" piece of glass from the bottom lap over onto the rear seat back. The glass cured to much and did not lay flat on the underside of the seat back. After the final cure of the tapes and rear seat back layup I sanded off the extra 2". I will lay up a couple plies of reenforcement glass in it's place. While I am not happy with this step not going as planned I am sure the final result will be o.k.

Also pictured, the transition from the front seat back to the fuselage bottom had a small gap. Somehow I carved away a little to much foam when I contoured the fuselage bottom. To remedy the situation I epoxied some foam into the gap and carved it down to a nice transition. Again I was not happy that this happend, but I believe the final result will work well.
















Tuesday, January 1, 2008

Chapter 6 - Fuselage bottom - Part 3


Today I glassed the fuselage bottom. Nothing interesting here. It was a lot like glassing the sides.
Tomorrow I will flox the bottom in place.

Sunday, December 30, 2007

Chapter 6 - Fuselage bottom - Part 2

After finally just resigning to the fact that this next step was going to make a big mess, I got to work and finished contouring the fuselage bottom. It did indeed throw blue bits everywhere
(not unlike a Unicef advertisement http://www.youtube.com/watch?v=7MAYrF1PDks)

I made a small mistake at the back seat area. I started to contour all the way to where the triangular longeron is to be bonded. I then realized this area should be left alone because the rear consoles would be located in that area. The damage was minimal and I should be able to fill it in after the consoles are installed. Measure twice, cut once!!!!




















I used an angle grinder with a heavy duty sanding disk for the majority of the work. This worked quite well. It cut through the foam like butter. It also made good work of my left index finger taking the skin off the the knuckle nearly down to the bone. I used a pair of work gloves my father sent me for X-mas after that little incident, thanks Dad. I also picked up a first aid kit when I was at the hardware store. I found that I only had a couple of little Sponge Bob bandages in the house.

After contouring the bottom I place it upside down on the fuselage as instructed in the plans.

I used 2 8' 1x4 peices of lumber cut to 7' with the 1' scraps used as shims to jig the bottom to the fuselage curve. The lumber was then bonded to the foam with small dabs of bondo to ensure the peice holds its curve for glassing.



Wednesday, December 26, 2007

Chapter 6 - Fuselage bottom - Part 1

I have started to contour the fuselage bottom, however my workshop is getting far to cluttered. I will need to stop for a little bit and regroup, clean and make sure my shop is ready for this step as it will generate a good deal of foam bits everywhere.

This is by far the worst shape my shop has been in since I was well into my Kayak project and I do not feel comfortable working on an aircraft project with this much clutter. Compare these photos to the first few when I started.